• Sets thickness of guard panel attached along side of vessel.

• Sets length of guard panel attached along side of vessel.

• Sets width of guard panel attached along side of vessel.

• Sets the offset between Air Intake connection at End1 and the bottom of equipment.

• 1-Back
• 2-Front
• 3-Left
• 4-Right
• 5-Top

• Puts Air Intake connection on one of the above sides of equipment box.

• Sets outside diameter of Air Intake connection of equipment (e.g. Boiler).

• Sets offset between Air Intake connection and side of equipment.

• Sets default thickness of the bars forming grille surface on the equipment (e.g. Catch Basin).

Base

• 1-Yes
• 2-No

• Sets or no base at the bottom of vessel (e.g. Air Separator).

• Sets height of the base attached to vessel bottom. Disabled when No Base is set.

• Sets distance between the two bars of base of boiler.

• Sets length of base bars, initially matching the length of the boiler.

• Sets distance between base and the bottom of the boiler tube.

• Sets height of the body, including control box.

• Sets length of the equipment body.

• Sets depth of the equipment body.

• Sets rating of boiler in Btu/Hr in Imperial and kW in Metric unit system.

• 1-RIRETUBE– for Fire Tube type boiler equipment.
• 2-WATERTUBE– for Water Tube type boiler equipment.

• Sets respective boiler types.

• Sets offset distance between End1 connect point and bottom of equipment.

• Sets vertical offset to Outlet1 connection at End2 from the bottom.

• Sets vertical offset to Outlet2 connection at End3 from the bottom.

Box | Length

• Sets dimensions of sides of equipment box.

Brackets Thickness

• Sets dimensions of pair of brackets placed on Dosing Pot.

  The length is additional value to the pot diameter.

• Library file name for device cells.

  For example, Vessel01.

• Sets the model cell displayed to the device.
• Scale entry fits cell proportionally to extents of device.

Positive <numeric value>

• Sets the offset between Chilled Water IN connection at End1 and the bottom of the Chiller unit.

• 1-left
• 2-right

• Puts the Chilled Water IN connection at End1 on one of the above sides of Chiller box.

• Sets outside diameter of Chilled Water IN connection at End1.

• Sets the offset between Chilled Water IN connection at End1 and the side of the Chiller unit.

• Sets the offset between Chilled Water OUT connection at End2 and the bottom of the Chiller unit.

• 1-left
• 2-right

• Puts the Chilled Water OUT connection at End2 on one of the above sides of Chiller box.

• Sets outside diameter of Chilled Water OUT connection at End2.

• Sets the offset between Chilled Water OUT connection at End2 and the side of the Chiller unit.

• Sets the straight length of (3)coils at Ends.

• Sets distance between End1 and the vessel body.

• Sets pipe outside diameter for End1 of water heater.

• 1-Type01
• 2-Type02
• 3-Type03

• Sets condenser type.
• Determines number of compressors; 1 compressor for Type01 and Type02 and 2 for Type03.

Condenser Water IN Bottom Offset

• Sets the offset between Chilled Water IN connection at End5 and the bottom of the Chiller unit.

• 1-left
• 2-right

• Puts the Condenser Water IN connection at End5 on one of the above sides of Chiller box.

• Sets outside diameter of Chilled Water IN connection at End5.

• Sets the offset between Chilled Water IN connection at End5 and the side of the Chiller unit.

• Sets the offset between Chilled Water OUT connection at End6 and the bottom of the Chiller unit.

• 1-left
• 2-right

• Puts the Condenser Water OUT connection at End6 on one of the above sides of Chiller box.

• Sets outside diameter of Chilled Water OUT connection at End6.

• Sets the offset between Chilled Water OUT connection at End6 and the side of the Chiller unit.

Connection 2 | Length (L2)

Connection 4 | Length (L4)

Connection 6 | Length (L6)

• Sets the straight length at:
  • End1
  • End2
  • End3
  • End4
  • End5
  • End6, respectively.

Connection2 Outer Diameter

• Sets pipe outside diameters for:
  • End1
  • End2
  • End3, respectively.

• Sets and sizes end with a flange connection.

• Sets and sizes end with a male connection.

• Sets and sizes end with a female connection.

Example: fl-2;fe-.13 creates a flange at End1 with size 2, and a female connection at End2 with an overall reduction of component's dimensions of .13

• 1-Back
• 2-Front
• 3-Left
• 4-Right

• Puts connection on one of the above sides of condenser box.

• Sets the electric connection type of boiler to single phase capacity.

• Sets the electric connection type of boiler to 3 Phase capacity.

• Sets height of the control box. Equals 1/10th of Body Height.

• 1-Back
• 2-Front
• 3-Left
• 4-Right
• 5-Top– exception Chillers.

• Puts control connection on one of the above sides of equipment box.

Control Length

• Sets dimensions of sides of control (box) placed on the equipment side.

• Sets offset between control box assembly and side of equipment.

• Sets offset between control box assembly and top of equipment.

• Sets depth of vessel cylinder / equipment tank.

• Sets outer diameter of vessel.

• Sets height of upper surface elevated above the cylinder of vessel.

• Sets offset between control Drain connection and bottom of equipment.

• 1-left
• 2-right

• Puts the Drain connection at End3 on one of the above sides of Chiller box.

Drain | Outer Diameter

• Sets outside diameter of drain connection.

• Sets the length of the pipe at drain connection.

• Sets the offset between Drain connection and side of equipment (e.g. at End3 of Chiller unit.)

• Sets the offset between Drain connection and top of equipment.

• Sets outside diameter of coil connection at End3.

• Sets length to straight portion at electric connection at End5.

• Sets width to portion at electric connection at End5.

• Sets the offset between Electric Supply connection and the bottom of equipment (e.g. Chiller).

• 1-Back
• 2-Front
• 3-Left
• 4-Right
• 5-Top

• Puts the Electric Supply connection on one of the above sides of equipment.

• Sets outside diameter of Electric Supply connection in the equipment.

• Sets the offset between Electric Supply connection and the side of equipment (e.g. Chiller).

• Sets offset to End3 connect point from left side on control box.

• Sets offset distance between End3 connect point and top of control box.

• Sets height of cylindrical fans placed on Chiller.

• Sets outside diameter of cylindrical fans placed on Chiller.

• Puts fan on top of condenser box.

• Puts fan on side of condenser box.

• Sets offset to fan from sides.

• Sets outside diameter of fans.

• Sets offset to fan from top, when placed at sides.

• Sets vertical offset to Flow connection from the bottom.

• 1-Back
• 2-Front
• 3-Left
• 4-Right
• 5-Top

• Puts Flow connection at End1 on one of the sides of the equipment.

• Sets outside diameter of Flow connection at End1 in equipment.

• Sets horizontal offset to Flow connection from the side.

• 1-Back
• 2-Front
• 3-Left
• 4-Right
• 5-Top

• Puts Flue connection on one of the above sides of boiler equipment box.

• Sets outside diameter of Flue connection at End5 in Boiler equipment.

• Sets horizontal offset to Flue connection from the side of equipment.

• Sets horizontal offset to Flue connection from the bottom of equipment.

• Sets a value for the amount of fuel flow through the equipment, in GpM in Imperial and l/s in Metric unit system. Used to calculate overall flow rate during analysis operations.

• 1-Gas

• Puts fan on top of condenser box.

• 2-Gas/Oil
• 3-Oil

• Puts fan on side of condenser box.

• Sets horizontal offset to Gas Inlet connection from the bottom.

• 1-Back
• 2-Front
• 3-Left
• 4-Right
• 5-Top

• Puts Gas Inlet connection on one of the above sides of boiler equipment box.

• Sets outside diameter to Gas Inlet connection.

• Sets horizontal offset to Gas Inlet connection from the side.

• Sets depth of grille portion.

• Sets offset to grille portion from right side. Negative offset shifts grille to the right. 0 offset aligns grille portion in the center of panel.

• Sets offset to grille portion from bottom side. Negative offset shifts grille down.

• Sets width of grille portion.

• Sets straight height of vessel cylinder / equipment tank.

• Sets distance between End1 and the vessel body.

• Sets pipe outside diameter for End2 of water heater.

Outlet 1 | Connection Side

• 1-Back
• 2-Front
• 3-Left
• 4-Right
• 5-Top
• 6-Bottom

• Puts the respective inlet / outlet connection on one of the above sides of equipment box.

• Sets length of Inlet pipe at End1, in addition to Connection1 Length.

• Sets outer diameter of the inlet connection (End1) of the equipment.

• Sets horizontal offset to Inlet connection from side of equipment.

• Sets vertical offset to Inlet connection from top of equipment.

• Sets straight height between center of End1/End2 and top of the equipment, equals default half of total height, and can be set higher

• Sets straight length of vessel cylinder / equipment tank.

• Sets outside diameter D1 of coil connection at End1.

• Sets offset to End1 connect point from right side on control box.

• Sets offset distance between End1 connect point and top of control box.

• 1-Steel
• 2-Concrete
• 3-GRP
• 4-Polyethene
• 5-Fiberglass

• Sets the storage tank body material.

• 1-Vertical - mounts vessel vertical.
• 2-Horizontal - mounts vessel horizontal.

• Sets the mounting orientation to the vessel.

• Positive <integer>
• 1
• 2

• Sets the number of compressor units in condenser.

• 1-Single
• 2-Double

• Sets number of air vents on the vent assembly on the top of Air Separator.

• Sets number of fan in the equipment.

• Sets number of horizontal bars.

• Sets number of strips on the side of round Catch Basin.

• Sets number of vertical bars.

• Sets offset between center of fans (for Type03).

• Sets length of outlet pipe at End2, in addition to Length 2.

• Sets length of additional outlet pipe at End3, in addition to Length 3.

• Sets outside diameter of connection at End1.

• Sets diameter of outlet pipe at End2.
• Sets outside diameter of outlet connection at End1. (for Catch Basin)

• Sets length of outlet pipe.

• Sets outside diameter of body of Dosing Pot equipment.

• Sets body length of Dosing Pot equipment.

• Sets offset to Return connection at End2 from bottom of equipment.

• 1-Back
• 2-Front
• 3-Left
• 4-Right
• 5-Top

• Puts Return connection at End2 on one of the sides of the equipment.

• Sets outside diameter of Return connection at End2 of equipment.

• Sets offset to Return connection at End2 from side of equipment.

Section Length

• Sets dimensions of the tank (when TankType is set Sectional).

• 1-Top
• 2-Bottom
• 3-Front
• 4-Back

• Puts shell inlet connection on one of the sides of the equipment.

• Sets outside diameter of shell inlet connection of Heat Exchanger at End3.

• Sets length of shell inlet connection of Heat Exchanger at End3.

• Sets horizontal offset distance of inlet connect point at End3 to the left of the side of heat exchanger.

• 1-Top
• 2-Bottom
• 3-Front
• 4-Back

• Puts shell outlet connection on one of the sides of the equipment.

• Sets outside diameter of shell outlet connection of Heat Exchanger at End4.

• Sets length of shell outlet connection of Heat Exchanger at End4.

• Sets horizontal offset distance of outlet connect point at End4 to the left of the side of heat exchanger.

• Sets horizontal offset to Inlet connection at End1 from the side.

• Sets horizontal offset to Outlet1 connection at End2 from the side.

• Sets horizontal offset to Outlet2 connection at End3 from the side.

• Sets height to the stand attached to the vessel body of Shell and Tube heat exchanger equipment.

• Sets width to the stand attached to the vessel body of Shell and Tube heat exchanger equipment.

• Sets default thickness to strips forming grille surface on the equipment (e.g. Catch Basin).

• Sets offset to End2 connect point from right side on control box.

• Sets offset distance between End2 connect point and top of control box.

• Sets outside diameter D2 of coil connection at End3.

• Sets tag value visible in output of drawing composition in dynamic view. Separate tag strings with a semi colon.

Tank Length

• Sets dimensions of sides of tank. Modified using the Section dimensions.

• 1- OnePiece
• 2- Sectional

• Sets the tank sectional or a single piece.

  When Sectional the tank dimension depicts that of Section.

• Sets offset distance between End2 connect point and top of equipment.

• Sets vertical offset to Inlet connection at End1 from the side.

• Sets distance between End1 and End2 of equipment.

• Sets the height from the base to the discharge port/manifold end 2 surface.

• Sets straight height from End3 connection at bottom to the vent at top, equals default twice the Height1.

• 1-RHS
• 2-LHS

• Sets tube inlet and outlet connections to either Left or Right side of unit.

• Sets outside diameter of tube inlet connection of Heat Exchanger at End1.

• Sets length of shell inlet connection of Heat Exchanger at End1.

• Sets horizontal offset distance of inlet connect point at End1 to the center of the side of heat exchanger the inlet is connected.

• Sets outside diameter of tube outlet connection of Heat Exchanger at End2.

• Sets length of shell outlet connection of Heat Exchanger at End2.

• Sets horizontal offset distance of outlet connect point at End2 to the center of the side of heat exchanger the outlet is connected.

• Sets outside diameter of body of Tundish equipment.

• Sets body length of Tundish equipment.

• Sets outside diameter of vent assembly housing the air vents on the top of equipment.

• Sets thickness of walls of tank unit.

• Sets width of equipment tank /vessel cylinder.